Table of Contents
A brand-new 3D printer can produce decent results out of the box, but calibration is what separates “good enough” prints from truly dialed-in quality. If you have ever dealt with rough first layers, inconsistent extrusion, or mysterious blobs, the fix is almost always proper calibration.
This guide walks you through every calibration step in the right order. Follow it once and your printer will reward you with cleaner, stronger, more accurate prints on every single job.
Why Calibration Order Matters
Each calibration step builds on the last. Tuning your flow rate before your e-steps are correct, for example, means you are compensating for a problem instead of fixing it. Follow these steps in sequence for the best results:
- Bed leveling
- E-steps calibration
- Flow rate tuning
- Temperature tower
- Retraction tuning
- First layer optimization
Step 1: Bed Leveling
A level bed is the foundation of every successful print. If your nozzle is too far from the bed, filament will not stick. Too close, and it drags through the plastic and causes jams.
Manual leveling (most printers):
- Home all axes and disable the stepper motors so you can move the print head by hand.
- Place a sheet of standard printer paper between the nozzle and the bed.
- Move the print head to each corner and adjust the leveling knob until the paper slides with slight resistance - you should feel a light drag but still be able to pull the paper out.
- Repeat the full cycle at least twice. Adjusting one corner changes the others slightly.
- Check the center last. If it is noticeably different from the corners, your bed may be warped and a glass or PEI sheet upgrade is worth considering.
Auto bed leveling (ABL): If your printer has a BLTouch, CR Touch, or inductive probe, run the automatic mesh leveling routine from the menu. Even with ABL, make sure your Z-offset is set correctly - run a single-layer test square and adjust until the first layer is smooth and slightly squished without being transparent.
Step 2: E-Steps Calibration
E-steps (extruder steps per millimeter) tell your printer how much the motor needs to turn to push exactly 1mm of filament. If this number is off, every other extrusion setting will be wrong too.
How to calibrate e-steps:
- Remove the bowden tube from the extruder (or, on a direct drive, disconnect the hotend so filament extrudes into open air).
- Load filament and use your printer’s menu or a terminal command to extrude exactly 100mm. On Marlin firmware, send
G1 E100 F100through a serial connection or OctoPrint. - Before extruding, mark the filament 120mm above the extruder entry point with a marker.
- After the extrusion finishes, measure the distance from your mark to the entry point. If it is exactly 20mm, your e-steps are perfect. If not, calculate the new value:
New E-steps = (Current E-steps x 100) / Actual mm extruded
For example, if your current e-steps are 93 and only 96mm was extruded: (93 x 100) / 96 = 96.875 new e-steps.
- Save the value with
M92 E96.875followed byM500to write it to EEPROM.
Run the test again to confirm. You should be within 0.5mm of the 100mm target.
Step 3: Flow Rate (Extrusion Multiplier)
With accurate e-steps, your flow rate fine-tunes how much plastic is actually deposited. This accounts for filament diameter variation, nozzle wear, and material behavior.
How to test flow rate:
- In your slicer, set the flow rate (or extrusion multiplier) to 100%.
- Print a single-wall cube - a hollow box with exactly one perimeter and zero infill and zero top layers. Many calibration model sets on Thingiverse or Printables include one.
- Measure the wall thickness with digital calipers in several spots.
- If your line width is set to 0.4mm and the wall measures 0.44mm, your flow is too high. Calculate:
New Flow Rate = (Expected Width / Measured Width) x Current Flow Rate
(0.4 / 0.44) x 100 = 90.9%
- Update the value in your slicer and reprint to verify.
Most well-calibrated printers land between 92% and 100% flow rate. If you are below 88%, double-check your e-steps first.
Step 4: Temperature Tower
Every filament - even the same brand in a different color - can print best at a slightly different temperature. A temperature tower prints a small section at multiple temperatures in a single print so you can compare surface quality, bridging, overhangs, and stringing all at once.
How to run a temperature tower:
- Download a temperature tower model. Popular options are available on Printables and Thingiverse by searching “temperature tower.”
- In your slicer, set up temperature changes at each section. In Cura, use the “ChangeAtZ” or “Modify G-Code” plugin. In PrusaSlicer or OrcaSlicer, you can add temperature changes per layer height in the custom G-code section.
- For PLA, a range of 190 to 220 degrees in 5-degree increments is a good starting point. For PETG, try 220 to 250. For ABS, try 230 to 260.
- After printing, inspect each section. Look for the level that has the smoothest walls, cleanest overhangs, best bridging, and least stringing.
- Set that temperature as your default for that specific filament in your slicer profile.
Write the winning temperature on the spool with a marker. You will thank yourself later when you swap filaments.
Step 5: Retraction Tuning
Retraction pulls filament back when the nozzle travels across empty space, preventing strings and blobs. The right settings depend on your extruder type.
Starting values:
- Bowden extruders (Ender 3, CR-10): 5-7mm retraction distance, 25-45mm/s retraction speed
- Direct drive (Bambu Lab, Prusa MK4, Voron): 0.5-2mm distance, 25-35mm/s speed
How to test retraction:
- Print a retraction test - two thin towers spaced apart so the nozzle has to travel between them. Search “retraction test” on any model site.
- Start with the values above and print a test. If strings are visible, increase retraction distance by 0.5mm and reprint.
- If increasing distance does not help past a certain point, try lowering the print temperature by 5 degrees. Temperature and retraction work together.
- Once strings are gone, do not increase retraction further. Over-retraction causes clogs and gaps in your extrusion.
For a deeper dive on stringing fixes, check out our guide to fixing stringing and oozing.
Step 6: First Layer Settings
Your first layer is the most critical. A perfect first layer means the rest of the print has a solid foundation. A bad one means wasted time and filament.
Optimized first layer settings:
- Speed: Slow it down. Set your first layer speed to 50-60% of your normal print speed, or around 20-30mm/s for most printers.
- Layer height: Use a first layer height of 0.2-0.28mm even if the rest of your print uses 0.12mm layers. A thicker first layer is more forgiving and sticks better.
- Line width: Set your first layer line width to 120-150% of your nozzle diameter. A 0.4mm nozzle should lay down 0.48-0.6mm first layer lines. The wider lines press harder into the bed for better adhesion.
- Temperature: Adding 5 degrees to your first layer temperature compared to the rest of the print improves flow and bed adhesion.
- Fan speed: Keep the part cooling fan off for the first 1-3 layers. Cooling the plastic immediately makes it shrink and pull away from the bed.
- Bed temperature: For PLA, 55-60 degrees. For PETG, 70-80 degrees. For ABS, 90-110 degrees.
Keep a Calibration Log
After working through all six steps, save your settings as a custom profile in your slicer. Label it with the filament brand, material, and color so you can reload it instantly. When you switch to a new filament, you usually only need to redo the temperature tower and flow rate steps - the mechanical calibrations (bed level, e-steps) stay valid until you change hardware.
Calibration takes about an hour of hands-on time and a few grams of filament. The payoff is hundreds of hours of reliable, high-quality printing with minimal failed prints and wasted material. Your future self will appreciate the effort.
If you are just getting started, our 3D printing beginner’s guide covers everything from choosing a printer to your first successful print.
Sponsored
Ready to Print?
Browse our guides for more tips on getting the best results from your printer.
Browse All GuidesReady to Print?
Browse our guides for more tips, reviews, and step-by-step tutorials to get the most out of your 3D printer.
Browse All Guides